Ferrari's Innovative Rear Wing Innovation at Risk for Melbourne Showdown
Following an impressive maiden appearance in Formula 1 competition, Ferrari's revolutionary rear wing design may not feature on the cars of Lewis Hamilton and Charles Leclerc when the circus arrives in Australia. The Scuderia's cutting-edge aerodynamic solution could be sidelined just days after its successful introduction to the sport.
Ferrari's groundbreaking rear wing technology, which made waves with its impressive Formula 1 premiere, faces an uncertain future at the Australian Grand Prix. The innovative component could be absent from both Lewis Hamilton and Charles Leclerc's vehicles when the championship heads down under.
The distinctive aerodynamic solution demonstrated considerable promise during its initial outing, but the Maranello team may opt to shelve the design for the Melbourne round. This potential decision comes just days after the rear wing's acclaimed introduction to the sport's highest level of competition.
Original source
GPFans
Related Regulations
Hover over badges for quick summaries, or scroll down for full official text and simplified explanations.
Full Regulation Text
Article C1.6
New systems or technologies
Chapter: ARTICLE C1: GENERAL PRINCIPLES
In Simple Terms
If a team invents a clever new system or technology that isn't explicitly mentioned in the rulebook but the FIA approves it, they can only use it for the rest of that season. Once the season ends, that innovation is no longer allowed unless it becomes an official part of the regulations.
- New technologies must be approved by the FIA before use
- Approved innovations are only permitted until the end of the season in which they're introduced
- Teams cannot carry over one-season innovations to the next season automatically
- The regulation prevents any team from gaining a permanent advantage from a loophole
Official FIA Text
Any new system, procedure or technology not specifically covered by these Technical Regulations, but which is deemed permissible by the FIA, will only be admitted until the end of the Championship during which it is introduced.
Article C3.11.1
Rear Wing Profiles
Chapter: C3
In Simple Terms
The rear wing must fit within a specific design area and can have up to three separate sections. It cannot have inward-curving surfaces visible from underneath, and any inward curves visible from above must have a minimum radius of 100mm to ensure safety and fair aerodynamic performance.
- Rear wing bodywork must stay within the defined RV-RW-PROFILES design box
- Maximum of three non-overlapping sections allowed in the rear wing structure
- No concave (inward-curving) surfaces allowed when viewed from below
- Any concave surfaces visible from above must have at least 100mm radius to prevent sharp curves
Official FIA Text
Rear Wing Profiles Bodywork must lie in its entirety within RV-RW-PROFILES, comprise of up to three non-intersecting simply connected volumes, and contain no concave radius of curvature visible from below and no concave radius less than 100mm visible from above.
Article C3.18.14
Rear Wing Skins
Chapter: C3
In Simple Terms
F1 rear wings must be rigid enough that their outer surfaces don't bend more than 2mm when a suction cup applies a pulling force to them. This test ensures wings stay stable and maintain their aerodynamic shape during races, preventing teams from using flexible wings as an unfair advantage.
- Rear wing skins can deflect no more than 2mm under 60N of force applied perpendicular to the wing surface
- A 50mm diameter vacuum cup is used to apply the test force
- Deflection is measured at the outer edge of the cup and compared to the lower wing surface at the same position along the wing
- The measurement point must be at least 300mm away from other reference points to ensure accurate testing
Official FIA Text
Skins of Rear Wing Profiles may deflect no more than 2mm when 60N force applied normal to and away from element. Force applied using vacuum cup of 50mm diameter. Deflection measured at outer diameter of cup and relative to lower wing surface at same X-Station, at least 300mm away.
Trending Articles
McLaren Frustrated by Limited Technical Disclosure from Mercedes Engine Program
about 1 hour ago
Stella Outlines McLaren's Path Forward Following Melbourne Reality Check
about 1 hour ago.webp&w=3840&q=75)
Melbourne Delivers: Six Standout Performers and Five Disappointing Campaigns from F1's Season Opener
about 1 hour ago
Beyond the Podium: Nine Hidden Gems from Australia's Grand Prix Weekend
about 1 hour ago
Your Complete Guide to the 2026 Chinese Grand Prix: Schedule, Viewing Options, and Essential Details
about 1 hour ago